PoE Power Budget Calculator (2026) — Size 4–16 Camera Systems Correctly
Free PoE power budget calculator for 802.3af / 802.3at / 802.3bt camera deployments.
Last updated: February 2026
This PoE budget calculator (also known as a PoE budget sizing tool or "PoE budget beräkning") helps you calculate total switch power requirements for IP cameras and edge AI deployments.
Also searching for "PoE budget beräkning"? This calculator works for global PoE deployments.
Quick Answer
Formula: Required PoE Budget (W) = (Cameras × W/camera + Switch overhead + Other devices) × (1 + Headroom ÷ 100)
Design Notes: Always use max power draw per camera from the manufacturer datasheet — not nominal or typical values. Include 5–15W for switch overhead unless the datasheet explicitly excludes it from the PoE budget. Use 20% headroom as a minimum; 25–30% for outdoor, PTZ, or IR-equipped deployments.
Example: 8 cameras at 8W each, 10W switch overhead, 25% headroom: (8 × 8 + 10) × 1.25 = 74 × 1.25 = 92.5W — select a 120W switch.
Verify both total PoE budget and per-port limit in the switch datasheet. The more restrictive limit applies.
PoE Budget Quick Reference (2026)
- 4 cameras × 8W + 25% headroom: ~40W → 60W switch tier
- 8 cameras × 8W + 25% headroom: ~80W → 120W switch tier
- 8 cameras × 15W + 25% headroom: ~150W → 180W switch tier
- 16 cameras × 15W + 25% headroom: ~300W → 370W switch tier
- PTZ cameras: Budget 25–30W per port; per-port limit is often the binding constraint
Rule: Check both total PoE budget and per-port limit — the more restrictive one determines your switch selection.
PoE Switch Tier Guide (Real-World Deployments)
| Deployment | Camera Config | Estimated Load (10W overhead + 25% headroom) | Recommended Switch Budget |
|---|---|---|---|
| 4-camera indoor | 4 fixed, 8W each | (32 + 10) × 1.25 = 52W | 60W |
| 8-camera standard | 8 fixed, 8W each | (64 + 10) × 1.25 = 93W | 120W |
| 8-camera with PTZ mix | 6 fixed (8W) + 2 PTZ (25W) | (98 + 10) × 1.25 = 135W | 180W |
| 16-camera fixed | 16 fixed, 10W each | (160 + 10) × 1.25 = 213W | 250W |
| 16-camera outdoor/PTZ mix | 12 fixed (10W) + 4 PTZ (25W) | (220 + 10) × 1.25 = 288W | 370W |
Note: Camera watts are max draw from datasheet; typical draw is often lower. PTZ values assume mid-range pan-tilt-zoom cameras at full IR load. Scale headroom to 30% for outdoor deployments.
For complete edge AI infrastructure planning, see guides on RAM sizing and Jetson NVMe endurance picks.
Calculator
Building a full edge AI node? See:
- 8-Camera Edge AI Deployment Blueprint — complete system sizing from PoE to compute
- NVMe vs SD Card for Jetson — storage selection for edge video nodes
- Best NVMe SSD for Jetson Orin Nano — endurance and thermal validation
- Edge AI RAM Sizing Guide — memory requirements for 1–8 camera inference pipelines
How to Use
- Enter the number of cameras and average watts per camera in your deployment.
- Select your PoE standard (PoE, PoE+, or PoE++) based on your switch and devices.
- Add any switch overhead or other PoE devices, then click Calculate to see your recommended budget and switch tier.
Why PoE Cameras Randomly Reboot at Night (And How to Prevent It)
The most common unexplained PoE camera outage pattern: cameras that run stably during the day begin power-cycling at dusk or in cold weather. The cause is predictable once you understand the load dynamics.
- IR LED activation: Cameras with infrared illumination activate their IR LEDs at low light. A camera rated at 8W typical can draw 12–15W with IR fully active. A switch running at 85–90% of its PoE budget during the day has no headroom for this spike and cycles the camera port.
- Cold temperature power draw: PTZ cameras and cameras with internal heaters draw measurably more in cold conditions. A PTZ rated at 20W nominal can approach its 30W maximum as internal heating circuits activate. This effect peaks at night when ambient temperatures drop furthest.
- Startup inrush current: A camera powering up after being cycled draws 1.5–2× its steady-state current for the first few seconds. If the switch's per-port limit is already near its ceiling, the inrush triggers another cycle — producing the oscillating reboot loop that is difficult to diagnose without a power meter on-site.
- Per-port limit vs. total budget mismatch: A switch may have total PoE budget available while still cutting power to a specific port if that port's per-port limit is exceeded. An 802.3af port (15.4W limit) cannot supply a camera requesting 16W at full IR load, regardless of how much total switch budget remains unused.
In edge AI deployments, this problem is amplified when PoE splitters or 802.3bt adapters power compute modules — Jetson-class devices, for example, are commonly powered via a dedicated PoE port drawing 15–25W depending on power mode. When a single PoE switch serves both cameras and edge compute nodes, the compute ports consume meaningful budget and may require PoE+ or PoE++ per-port allocation. A Jetson Orin Nano in 15W mode should be budgeted as a PoE+ class load (802.3at, 30W PSE) once splitter losses and peak draw are included; mixing such a device with IR cameras on an 802.3af switch (15.4W per-port limit) will produce per-port failures even when total switch budget appears sufficient. Validate each port's peak draw independently when mixing camera and compute loads on a single switch.
The fix is consistent: size headroom correctly at design time (20–30% above max draw, not typical draw) and verify per-port limits against worst-case camera power, not nominal camera power.
Why this matters: Undersizing a PoE switch is the most common cause of intermittent IP camera outages — cameras power-cycle when the switch's total budget is exceeded, and the root cause is rarely obvious from symptoms alone. A 10-minute budget calculation prevents months of on-site troubleshooting.
Engineering Summary
- Total budget and per-port limits are independent constraints: A 250W switch with 30W per-port limits cannot power a 25W PTZ camera if that port's limit is exceeded — even with total budget available. Always apply both limits and use the more restrictive.
- Headroom is not optional: PoE cameras draw more at startup, on IR activation, and in cold temperatures. Switches running above 90% of rated budget will cycle cameras under peak load. 20–30% headroom protects against these transients.
- IEEE standards define power at the PSE, not at the device: 802.3af/at/bt specifies maximum wattage at the switch port (PSE — Power Sourcing Equipment), not guaranteed delivered power at the camera (PD — Powered Device). In practice, a 30W (PoE+) port typically corresponds to ~25.5W available at the device after cable loss (varies by run length and implementation). Size camera compatibility against PD power, not PSE power.
- Cable quality affects usable power: Thin or low-quality Cat5e runs longer than 50m lose voltage, reducing effective power at the camera. Use Cat6 for runs over 50m; never rely on the 100m Ethernet max for PoE at full camera load.
- Switch overhead is real: Management circuitry and uplink ports draw from the same PoE budget on some switch models. Include 5–15W switch overhead unless the datasheet explicitly excludes it from the PoE power envelope.
- Verify the datasheet, not the marketing spec: Advertised PoE budgets sometimes reflect theoretical totals, not sustained real-world output. Confirm the actual PoE power budget from the datasheet power supply section — not the product page headline.
PoE Budget Formula
Required Budget (W) = (Cameras × W/camera + Switch overhead + Other PoE devices) × Headroom multiplier
Headroom multiplier = 1 + (headroom % ÷ 100). Standard value: 1.25 for 25% headroom. Example: 8 cameras at 10W, 10W switch overhead, 25% headroom: (80 + 10) × 1.25 = 112.5W → select a 120W switch.
PoE Standards Reference
| Standard | Max per Port | Typical Use Case | Common Camera Types |
|---|---|---|---|
| 802.3af (PoE) | 15.4W | Fixed dome cameras, access points | Standard fixed IP cameras ≤12W |
| 802.3at (PoE+) | 30W | PTZ cameras, cameras with heaters | PTZ, varifocal, cameras with IR |
| 802.3bt Type 3 (PoE++) | 60W | High-power PTZ, edge AI compute nodes | High-end PTZ, Jetson-class edge nodes |
| 802.3bt Type 4 (PoE++) | 100W | Specialty high-power devices | Rare for cameras; thin clients, displays |
Decision Checklist
- ☐ Looked up max power draw for each camera in the manufacturer datasheet (not the product page)?
- ☐ Verified both total PoE budget and per-port limit for the selected switch — and applied the more restrictive?
- ☐ Added ≥20% headroom for startup peaks, IR activation, and cold-temperature power draw?
- ☐ Accounted for switch overhead and any non-camera PoE devices sharing the budget?
- ☐ Confirmed Cat6 cable for runs over 50m, or budgeted for voltage loss on Cat5e long runs?
FAQ
What is PoE headroom?
Headroom is extra budget to handle peak loads and inefficiencies in cable runs. A 20–30% safety margin is standard for edge deployments.
How do I know my camera's power draw?
Check your camera's datasheet for "max power consumption" or "PoE power." Typical PoE+ IP cameras draw 5–15W; check the manufacturer specs.
How many watts does an IP camera use?
Most PoE IP cameras draw 5–15W. PTZ cameras can draw 20–30W depending on IR and motor activity.
Why does cable length matter?
Longer cable runs lose voltage over distance, reducing power available to the camera. The PoE standard accounts for this, but poor quality cables amplify the loss.
What if my switch has per-port limits different from the standard?
Some switches limit each port below the standard (e.g., 20W per port on a PoE+ switch). Always verify your switch datasheet and apply the most restrictive limit.
Planning a Full Deployment?
This calculator covers PoE infrastructure sizing — one layer of a multi-layer design. A production edge AI node also requires compute sizing (RAM tier, NVMe endurance), camera network design (VLANs, bandwidth budgeting), power protection (UPS sizing, graceful shutdown), and inference pipeline configuration. These decisions interact: camera count drives PoE budget, which informs switch selection, which affects network topology, which determines compute node placement.
Try the Power Budget Planner tool for interactive sizing of the full system, or see the 8-Camera Edge AI Deployment Blueprint for a complete design specification covering PoE, compute, storage, networking, and monitoring.